MIRCRO SPRAY GARDEN WATERING KITS 08SP and 14SP

Parts List

ITEM	08SP	14SP	DESCRIPTION	PART #
	1	1	Hose  Filter 3/4" Female Hose x Male Hose 120 Mesh Poly Screen	A4-HTTF150
	1	1	Pressure Regulator 25 PSI - Hose Threaded 3/4" FHT x 3/4" MHT - High Quality Model	DD-HPR25
	1	1	Direct-Loc Swivel Adapter .600 ID DL x 3/4" FHT Swivel - 700 or 710 Tubing	DL-FHS600
	5	8	Direct-Loc Elbow .600 ID DL x DL - 700 or 710 Tubing	DL-L600
	1	4	Direct-Loc Tee .600 ID - 700 or 710 Tubing	DL-T600
	2	4	Direct-Loc End Cap .600 ID DL x 3/4" MHT w/ Cap - 700 or 710 Tubing	DL-EC600
	1	2	Direct-Loc Flow Control Shut off Valve	DL-FCV600
	1	0	1/2" x 50' .700 OD Poly Tubing - 50' Roll	DD-DH700-50
	0	1	1/2" x 50' .700 OD Poly Tubing - 100' Roll	DD-DH700-100
	1	0	1/4" x 50' .250 OD Poly Tubing - 50' Roll	DD-DH250-50
	0	1	1/4" x 100' .250 OD Poly Tubing - 100' Roll	DD-DH250-100
	1	1	Hole Punch for 1/4" Barbed Fittings & Drippers	DD-KP
	8	14	1/4" Barbed Connector	DD-C250
	10	10	Goof Plug - Dual End 1/4" & 1/8"	DD-GP
	8	14	13" Micro Jet Clip Stake	DD-MJCS13
	8	14	12" Micro Jet Riser With Barb	DD-MJRB12
	4	8	Quarter Circle Adjustable Micro Jet Sprayer	DD-MJVQ
	4	6	Half Circle Adjustable Micro Jet Sprayer	DD-MJVH
	1	1	Drip Tubing Hold Down 8" Wire Stake "J Style" fits 1/8" to 3/4" tubing -25 pack	TLS6
	10	20	1/2" Hold Down Clamp with Nail	DD-MC700

MIRCRO SPRAY GARDEN WATERING KITS 08SP and 14SP

Sample Set Up
1. Water Source Connection Assembly
Your Water Source Connection should be assembled as illustrated below. Please note, Water Source Connections included with this kit are not meant to be installed
under constant water pressure.
 

2. Layout Distribution Lines
Using Hold Down Stakes and Clips provided with the kit, layout your desired
layout using the ½” tubing and Perma-Loc Fittings provided. Below is a
sample layout for 2 raised beds.

3. Assemble and Install Micro Jet Sprayer Assemblies
Plan your placement for Spray Assemblies. It is suggested you place the
assemblies in the desired location prior to cutting any ¼” tubing. Once
assemblies are in the desired location, measure and cut ¼” leaving extra
length for placement adjustment.

Once assemblies are in place and ¼” tubing is cut to length, insert the
DD-C250 into the end of the ¼” tubing (if you are installing in cold conditions
dip the end of the ¼” tubing in hot water to make installation easier. Next
punch a hole using the hole punch provided and insert the assembly into the
hole to complete the installation.
 

4. Testing the System
Once the system set up is complete, turn on your water source slowly at first
to release air in the system. Once up and running you can adjust the spray
radius of each spray head for desired spray radius.
 

Maintenance Tips:  

WINTERIZING: For instructions click here

For more information on Drip Irrigation Design and Installation click here

Ref. 5280